The SIP-S V1.0 serial protocol is what the 60 GHz / 24 GHz modules stream over UART at 115200 / 8N1. This article gives a minimal, runnable Python parser that finds frames, validates the checksum, and prints the decoded fields — the bridge from “wires connected” (see the Bring-Up checklist) to “data in your code”.

Frame structure (SIP-S V1.0)

From the SIP-S V1.0 definition in the module user manuals (e.g. R60ABD1 user manual v3.6 §8.1):

Serial: 115200 bps, 8 data, 1 stop, no parity, no flow control; 3.3 V TTL; module TX → MCU/adapter RX.

Control-byte classes (from the same manual): 0x01 heartbeat, 0x02 product info, 0x03 OTA, 0x05 work state, 0x07 detection-range info, 0x80 presence, 0x81 breathing, 0x84 sleep, 0x85 heart rate. Semantics are module-specific — the fall module defines its own command set; the parser below is protocol-generic.

Minimal Python parser

import serial

HEADER = b'\x53\x59'
FOOTER = b'\x54\x43'

def parse_frames(buf):
    """Yield (control, command, data) for each valid frame in buf."""
    i = 0
    while True:
        head = buf.find(HEADER, i)
        if head == -1:
            return
        if len(buf) - head < 9:   # header+ctrl+cmd+len+chk+footer minimum
            return
        ctrl = buf[head + 2]
        cmd = buf[head + 3]
        length = (buf[head + 4] << 8) | buf[head + 5]   # big-endian
        data_start = head + 6
        data_end = data_start + length
        frame_end = data_end + 1 + 2   # checksum + footer
        if len(buf) < frame_end:
            return
        data = buf[data_start:data_end]
        checksum = buf[data_end]
        footer = buf[data_end + 1:frame_end]
        expected = sum(buf[head:data_end]) & 0xFF
        if checksum == expected and footer == FOOTER:
            yield (ctrl, cmd, data)
        i = head + 2

ser = serial.Serial('/dev/ttyUSB0', 115200, timeout=1)  # Windows: 'COM3'
buf = b''
while True:
    chunk = ser.read(64)
    if not chunk:
        continue
    buf += chunk
    for ctrl, cmd, data in parse_frames(buf):
        print(f"ctrl=0x{ctrl:02X} cmd=0x{cmd:02X} len={len(data)} data={data.hex()}")
    buf = buf[-256:]   # keep only the tail to bound memory

Test it without hardware

The manual (§4.5) gives a sample frame 53 59 80 81 00 01 0F with checksum computed as 0x53+0x59+0x80+0x81+0x00+0x01+0x0F = 0x01BD, so the checksum byte is 0xBD. The full frame is 53 59 80 81 00 01 0F BD 54 43 (10 bytes). Feed it straight to the parser:

sample = bytes.fromhex('5359808100010FBD5443')
print(list(parse_frames(sample)))
# -> [(0x80, 0x81, b'\x0f')]

(That sample is the manual’s own test vector — a presence/breathing report from the sleep module. Your fall module’s frames use its own command set, but the frame shape and checksum are identical.)

Extending it

• Map ctrl to a name using the control-byte table above for logging.
• The data field’s meaning depends on cmd and the module; consult that module’s command table in its user manual before interpreting values.
• On an MCU the same loop ports directly: scan for 0x53 0x59, read the length, accumulate, verify the checksum, then act on the payload.

Why this matters

GPIO gives a 1-bit “something happened” with zero parsing. UART gives the full state — and this parser is the minimum to turn the byte stream into structured data. Use both: GPIO for an instant local alarm, UART for records and dashboards.

Where to go next

• Get the wires right first: Bring-Up checklist.
• The GPIO/UART split: GPIO vs UART.
• Full specs: Module spec sheet.
• Tuning: Fall radar guide, Presence radar guide.

Evaluation units are on Tindie.